Lego Pick-A-Brick Website for Parts Purchasing
Make sure to only include the names before the color is listed so the correct piece(s) pop up.
| Flower 1x1 Light Purple (Pink) | 12 pieces |
| Flower 1x1 Bright Yellowish Green (Lime) | 12 pieces |
| Plant w/ Plate 1x1, No.1 Bright Yellowish Green (Lime) | 12 Pieces |
| Stalk w/ 1.5 Shaft and 3.2 Shaft Dark Green | 2 Pieces |
| Round Brick 1x1 Reddish Brown (Brown)* | 2 Pieces |
| Plate 4x8 Dark Green | 1 Piece |
| Brick 2x6 Reddish Brown (Brown)* | 1 Piece |
| Tile 1x8 Dark Stone Grey (Grey) | 2 Pieces |
| Tile 1x2 Dark Stone Grey (Grey) | 2 Pieces |
| Tile 1x2 Medium Stone Grey (Light Grey) | 2 Pieces |
| Roof Tile, 1x1x2/3, ABS Medium Stone Grey (Light Grey) | 4 Pieces |
| Flat Tile 1x1, Round Medium Stone Grey (Light Grey) | 4 Pieces |
| Plate 1x4 Dark Stone Grey (Grey) | 2 Pieces |
| Plate 1x6 Dark Stone Grey (Grey) | 2 Pieces |
| Brick 1x2 Medium Stone Grey (Light Grey) | 4 Pieces |
| Brick 1x2 w/ 2 Knobs Medium Stone Grey (Light Grey) | 2 Pieces |
| Brick 1x4 w/ 4 Knobs Medium Stone Grey (Light Grey) | 2 Pieces |
Total: 68 Pieces
*Note that Brown pieces can be fragile after extended use/age.*
Foliage Steps
!!!Foliage steps will be repeated twice!!!
Step 1: Take 6 of each of your Flower pieces and 6 of your Plant pieces. Place the Pink Flower pieces on the top stud of the Plant pieces, one for each. Do the same for the Lime flower pieces, placing them on the bottom instead.
Step 2: Place your decorated Plant pieces onto the Stalks, having the flowers show on top. The leaves of the Plant pieces should face downward.
Planting Steps
Step 3: Grab your 4x8 Plate. This will be the Base Plate for the buiild.
Step 4: Grab your 1x6 and 1x4 Plates. Place the 1x4s on the short edges of the Base Plate (4x8) and the 1x6s on the long edges. Areas are highlighted to aide. Red is for 1x4, Blue is for 1x6.
Step 5: Grab all of your Light Grey Bricks. Follow the image below for placement of Bricks on top of Dark Grey Tiles. 1x2 Brick is Green, 1x4 Knob is Blue, 1x2 Knob is Red.
Step 6: Take your Dark grey Tile pieces. Place the 1x2 Tiles on top of the 1x2 Knobs Bricks. On the long sides, place the 1x8 Tiles.
Step 7: To decorate the 1x4 Bricks' Knobs, grab your Round Tiles and 1x2 Light Grey Tiles. Place the 1x2 Tile in the middle, with the Round Tiles on either side. Do this for both Bricks.
Step 8: To decorate the 1x2 Bricks' Knobs, grab your Roof Tile/Cheese Wedge pieces. Place them as the image shows. It should match the view from a top-down perspective.
Step 9: Slot the Brown Brick into the hole that the thinner Bricks have made. Make sure to press firmly in order for the pieces to click together.
Step 10: Place your Round Brown Bricks in the highlighted spaces. You should have two of these pieces.
Step 11: Grab your Foliages. Slot them into the tops of the Round Brown Bricks by the bottom stem part.
Your final model should look like the image below. If not, make sure to look over all steps to ensure they have been followed correctly.
